ALC 68C Remote

Betrieb, Bau und Modifikation von Netzteilen.
Post Reply
shadow
Posts: 2
Joined: Mon 24 Nov, 2003 8:09 pm

ALC 68C Remote

Post by shadow » Mon 24 Nov, 2003 8:26 pm

Hallo zusammen....
sitze hier gerade im Labor vor einem kleinen Problem (eigentlich 2):
1) hat jemand die Schaltpläne vom ALC 68C Netzteil ?
2) Wer hat eine genaue Belegung für die Sub-D9 Schnittstelle des PSU vom ALC 68C ? Mir fehlt nämlich die Fernbedienung..... aber an sich sollte die doch nachbaubar sein..!?

Bitte um umgehende Hilfe wenn jemand Infos hat !

john
Posts: 1823
Joined: Wed 13 Jun, 2001 12:00 pm
Location: Berlin

Post by john » Mon 24 Nov, 2003 10:01 pm

Hi,

ohne Gewähr: Pin1 und Pin5 hängen dierkte (oder über Vorwiderstände?) am Optokoppler. Eine Steuerspannung zwischen 0 und x Volt regelt den Strom. Häng ein Amperemeter rein, mehr als 10mA würde ich dem Optokoppler nicht geben. Polarität weiß ich nicht mehr, kann aber beim Optokoppler nichts zerstören. Am besten ein Labornetzteil ran, auf Null reglen, und die Spannung langsam hochdrehen und den Strom durch den Optokoppler im Auge behalten. Evtl. einen 1K Widerstand in Reihe schalten, um auf Nummer sicher zu gehen.
Wenn sich der Röhrenstrom nicht regeln läßt, Polarität umkehren.

Manche ALC Netzteile (z.B. bei Meditec EIL4000 Variante) haben einen Strommessausgang an der Buchse. Da liegt dann ein Abgriff über dem internen Shunt, der in Reihe mit der Passbank liegt. Vorsicht! Netztpotentilal.

Gruß

John

PS: EIL4000 Plan habe ich elektronisch hier, ALC68 Plan nur als Papiervariante. Bei Interesse: eMail.

lxdoubleyou
Posts: 173
Joined: Sat 04 Jan, 2003 2:37 pm
Location: Munich

Post by lxdoubleyou » Tue 25 Nov, 2003 4:54 pm

Hi,

also der Pin 1 gehört an + und der 5er an 0V. Geregelt wird mit einer Spannung von 0-5V, wenn die Polarität nicht stimmt passiert gar nichts, wenn die Spannung über 5V geht dann rauchts ;-) Noch was: Die Regelung erfolgt nicht linear, bei meinem NT geht´s erst bei 1,2V los und bei 3,5V habe ich dann schon fast Volldampf. Ist glaube ich abhängig vom min. und max. Röhrenstrom der eingestellt ist.
Hoffe geholfen zu haben.

Grüße,
Alex

shadow
Posts: 2
Joined: Mon 24 Nov, 2003 8:09 pm

Post by shadow » Tue 25 Nov, 2003 6:09 pm

Danke für Eure schnelle Info, werde das hier mal ausprobieren und sehn ob das Rohr anspringt.
Wäre nett wenn Du mri den Schaltplan des ALC mal scannen und mailen könntest.

Greetz shadow

john
Posts: 1823
Joined: Wed 13 Jun, 2001 12:00 pm
Location: Berlin

Post by john » Tue 25 Nov, 2003 6:37 pm

Hallo Shadow,

was meinst du mit "Rohr anspringen"? Die Fernsteuerungsbuchse hat im Normalzustand nichts mit Starten zu tun! Du kannst nur den Strom zwischen Standby und Maximal regeln.

John

User avatar
rheinperchten
Posts: 394
Joined: Tue 08 Mar, 2005 2:38 pm
Location: Leverkusen
Contact:

Post by rheinperchten » Tue 24 Jan, 2006 11:42 pm

Also um das Uraltthema nochmal aufzugreifen.......
Habe ein EIL 4000 und möchte per Fernsteuerung den Strom regeln.
Wer hat sende bitte mal ne genaue Belegung und nen Tip wie man das macht...biiiiiittteeee :lol:
rheinperchten@gmx.de

User avatar
pitchoun
Posts: 500
Joined: Tue 24 May, 2005 12:24 am
Do you already have Laser-Equipment?: divers
Location: Haute-Loire

Post by pitchoun » Tue 21 Feb, 2006 3:57 am

Hello,
I have an Meditec EIL 4000 PSU and i must build my own remote.

But i haven't really understand the topic because i don't speak german :cry: and google translation is very bad.

So any can give to me the schematics of the remote ? or translate me the most important point of topic in english or french ?

And if someone can give me the schematics of the full power supply, it will be very helpfull for me.

you can contact me by private message or my email is pitchoun43@msn.com

thanks a lot
Euh j'ai dit une bétise ?!

User avatar
pitchoun
Posts: 500
Joined: Tue 24 May, 2005 12:24 am
Do you already have Laser-Equipment?: divers
Location: Haute-Loire

Post by pitchoun » Tue 21 Feb, 2006 3:59 am

Hello,
I have an Meditec EIL 4000 PSU and i must build my own remote.

But i haven't really understand the topic because i don't speak german :cry: and google translation is very bad.

So any can give to me the schematics of the remote ? or translate me the most important point of topic in english or french ?

And if someone can give me the schematics of the full power supply, it will be very helpfull for me.

you can contact me by private message or my email is pitchoun43@msn.com

thanks a lot
Euh j'ai dit une bétise ?!

User avatar
rheinperchten
Posts: 394
Joined: Tue 08 Mar, 2005 2:38 pm
Location: Leverkusen
Contact:

Post by rheinperchten » Tue 21 Feb, 2006 10:06 am

To control the Power of the laser, you can use the Sub-D on the backside of the power supply. You must take Pin 1 and Pin 5. Pin 1 is + and the Pin 5 is 0 ground. Use 0 to 5 Volts to regulate. Use a 1k resistor for security.

User avatar
pitchoun
Posts: 500
Joined: Tue 24 May, 2005 12:24 am
Do you already have Laser-Equipment?: divers
Location: Haute-Loire

Post by pitchoun » Tue 21 Feb, 2006 4:13 pm

I have done this small schématics, is it good ?
Image

Where i must add a 1K resistor ?


The PSU have 2 potentiometer for MIN and MAX current adjust. Actually my PSU can give 35A but my tube (Omnichrome 543) can only get 15A max. So how can i do the adjustment without over current the tube ?

i should decrease the value to MIN and slowly increase them to get the max current tube ?

Thanks a lot to fast response and sorry to have posted 2 time the same reply.
Euh j'ai dit une bétise ?!

User avatar
Dr. Burne
Posts: 2385
Joined: Tue 07 Aug, 2001 12:00 pm
Do you already have Laser-Equipment?: Pangolin Pro und Intro inkl. Beyond
Jede Menge alte Lasertechnik die groß und schwer ist
Baue grad pure Diode Main Projektor aus und 2 LW DS900
Molectron Powermeter mit PM1 und 10 Sonde
Location: Halle(Saale)
Contact:

Post by Dr. Burne » Tue 21 Feb, 2006 6:44 pm

Hi,


the max tube current is easyly to adjust.
Turn the tunable resistor until the tube current at 15A decreases, then you can tune the max current with both resistors(Remote + max.).



Greetz Stefan

User avatar
rheinperchten
Posts: 394
Joined: Tue 08 Mar, 2005 2:38 pm
Location: Leverkusen
Contact:

Post by rheinperchten » Tue 21 Feb, 2006 7:09 pm

I have send you some plans of the Meditec..........with mail

User avatar
pitchoun
Posts: 500
Joined: Tue 24 May, 2005 12:24 am
Do you already have Laser-Equipment?: divers
Location: Haute-Loire

Post by pitchoun » Tue 21 Feb, 2006 7:24 pm

Thanks a lot !!

I have been received the schematics.

I will post the following of my project here
if you want to look after it.

Thanks
Euh j'ai dit une bétise ?!

Post Reply

Return to “Netzteile”

Who is online

Users browsing this forum: No registered users and 1 guest